尊敬的用户，您好！欢迎登陆艾逊！
用户名 密码
忘记密码

校准标定

气动液压国际标准目录
 说明：Amd－编辑性修改；Cor－技术勘误；TR－技术报告；TS－技术规范。
标准编号后面的括号内是复审确认年代。

ISO/TC131  流体传动系统
ISO 5596:1999
Hydraulic fluid power － Gas-loaded accumulators with separator －Ranges of pressures and volumes and characteristic quantities
液压传动－隔离式充气蓄能器－压力和容积范围及特征量
ISO 10945:1994
Hydraulic fluid power － Gas-loaded accumulators －Dimensions of gas ports
液压传动－充气蓄能器－气口尺寸
ISO 10946:1999
Hydraulic fluid power － Gas-loaded accumulators with separator －Selection of preferred hydraulic ports
液压传动－隔离式充气蓄能器－优先选择的液压油口
ISO 16030:2001
Amd.1:2005
Pneumatic fluid power －Connections－Ports and stud ends
气压传动－连接件－气口和螺柱端
ISO 19973-1:2007
Pneumatic fluid power － Assessment of component reliability by testing － Part 1: General procedures
气压传动－元件可靠性的试验评价－第1部分：一般程序
ISO 19973-2:2007
Pneumatic fluid power － Assessment of component reliability by testing － Part 2: Directional control valves
气压传动－元件可靠性的试验评价－第2部分：方向控制阀
ISO 19973-3:2007
Pneumatic fluid power － Assessment of component reliability by testing － Part 3: Cylinders with piston rod
气压传动－元件可靠性的试验评价－第3部分：带活塞杆的气缸
ISO 19973-4:2007
Pneumatic fluid power － Assessment of component reliability by testing – Part 4: Pressure regulators
气压传动－元件可靠性的试验评价－第4部分：调压器
TC131/SC1 术语、分等和符号
ISO 1219-1:2012
Fluid power systems and components － Graphic symbols and circuit diagrams －Part 1: Graphic symbols for conventional use and data-processing applications
流体传动系统和元件－图形符号和回路图－第1部分：用于常规用途和数据处理用的图形符号
ISO 1219-2:1995
Fluid power systems and components － Graphic symbols and circuit diagrams －Part 2: Circuit diagrams
流体传动系统和元件－图形符号和回路图－第2部分：回路图
ISO 2944:2000
Fluid power systems and components － Nominal pressures
流体传动系统和元件－公称压力
ISO 5598:2008
Fluid power systems and components － Vocabulary
流体传动系统和元件－词汇
TC131/SC2  泵、马达和整体传动装置
ISO 3019-1:2001
Hydraulic fluid power － Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors －Part 1: Inch series shown in metric units
液压传动－容积式泵和马达的安装法兰和轴伸的尺寸及标注代号－第1部分：用米制单位表示的英制系列
ISO 3019-2:2001
Cor.1:2006
Hydraulic fluid power － Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors －Part 2: Metric series
液压传动－容积式泵和马达的安装法兰和轴伸的尺寸及标注代号－第2部分：米制系列
ISO 3662:1976
Hydraulic fluid power － Pumps and motors －Geometric displacements
液压传动－泵和马达－几何排量
ISO 4391:1983
Hydraulic fluid power － Pumps, motors and integral transmissions －Parameter definitions and letter symbols
液压传动－泵、马达和整体式传动装置－参数定义和字母代号
 
TC131/SC3  缸
ISO 3320:1987
（2008）
Fluid power systems and components － Cylinder bores and piston rod diameters －Metric series
流体传动系统和元件－缸内径和活塞杆直径－米制系列
ISO 3321:1975
Fluid power systems and components － Cylinder bores and piston rod diameters －Inch series
流体传动系统和元件－缸内径和活塞杆直径－英制系列
ISO 4393:1978
Fluid power systems and components － Cylinders －Basic series of piston strokes
流体传动系统和元件－缸－活塞行程基本系列
ISO 4394-1:1980
Fluid power systems and components － Cylinder barrels －Part 1: Requirements for steel tubes with specially finished bores
流体传动系统和元件－缸筒－第1部分：对有特殊精加工内孔钢管的要求
ISO 4395:2009
Cor.1:2010
Fluid power systems and components － Cylinders piston rod end types and dimensions
流体传动系统和元件－缸活塞杆端型式和尺寸
ISO 6020-1:2007
Hydraulic fluid power － Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series －Part 1: Medium series
液压传动－单杆缸安装尺寸－16 MPa  (160 bar)系列－第1部分：中型系列
ISO 6020-2:2006
Cor.1:2008
Hydraulic fluid power － Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series －Part 2: Compact series
液压传动－单杆缸安装尺寸，16MPa(160bar)系列－第2部分：紧凑型系列
ISO 6020-3:1994
Hydraulic fluid power － Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series －Part 3: Compact series with bores from 250 mm to 500 mm
液压传动－单杆缸安装尺寸，16MPa(160bar)系列－第3部分：缸内径250mm至500mm紧凑型系列
ISO 6022:2006
Hydraulic fluid power － Mounting dimensions for single rod cylinders,  25 MPa(250 bar) series
液压传动－25 MPa (250bar) 系列单杆缸安装尺寸
ISO 6099:2009
Fluid power systems and components － Cylinders －Identification code for mounting dimensions and mounting types
流体传动系统和元件－缸－安装尺寸和安装型式的标注代号
ISO 6430:1992
Pneumatic fluid power － Single rod cylinders, 1 000 kPa (10 bar) series, with integral mountings, bores from 32 mm to 250 mm －Mounting dimensions
气压传动－单杆缸，1000kPa(10bar)系列，整体式安装，缸内径32mm至250mm－安装尺寸
ISO 6432:1985
Pneumatic fluid power － Single rod cylinders,10 bar (1 000 kPa) series －Bores from 8 to 25 mm －Mounting dimensions
气压传动－单杆缸，10bar (1000kPa)系列，缸内径8mm至25mm－安装尺寸
ISO 6537:1982
Pneumatic fluid power systems － Cylinder barrels －Requirements for non-ferrous metallic tubes
气压传动系统－缸筒－对有色金属管的要求
ISO 7180:1986
Pneumatic fluid power － Cylinders －Bore and port thread sizes
气压传动－缸－缸内径和气口螺纹规格
ISO 7181:1991
(2006)
Hydraulic fluid power － Cylinders －Bore and rod area ratios
液压传动－缸－活塞和活塞杆面积比
ISO 8132:2006
Hydraulic fluid power － Single rod cylinders, 16MPa (160bar) medium and 25 MPa (250 bar ) series －Mounting dimensions for accessories
液压传动－单杆缸，16MPa (160bar )中型系列和25MPa (250bar ) 系列－附件安装尺寸
ISO 8133:2006
Hydraulic fluid power － Single rod cylinders, 16MPa (160bar) compact series －Mounting dimensions for accessories
液压传动－单杆缸，16MPa(160bar)，紧凑型系列－附件安装尺寸
ISO 8139:2009
Pneumatic fluid power - Cylinders, 1000 kPa (10 bar) series - Mounting dimensions of rod-end spherical eyes
气压传动－缸，1000kPa(10bar)系列－杆端球面耳环的安装尺寸
ISO 8140:2009
Pneumatic fluid power －Cylinders, 1000 kPa (10 bar) series －Mounting dimensions of rod-end clevis
气压传动－缸，1000kPa(10bar)系列－杆端环叉的安装尺寸
ISO 10099:2001
(2006)
Pneumatic fluid power － Cylinders －Final examination and acceptance criteria
气压传动－缸－验收试验
ISO 10100:2001
（2006）
Hydraulic fluid power － Cylinders －Acceptance test
液压传动－缸－验收试验
ISO 10762:1997
 (2008)
Hydraulic fluid power － Cylinder mounting dimensions －10 MPa (100 bar) series
液压传动－缸安装尺寸－10MPa(100bar)系列
ISO/TS 13725:2001
Hydraulic fluid power －Cylinders －Method for determining the buckling load
液压传动－缸－评定弯曲载荷的方法
ISO 13726:2008
Hydraulic fluid power － Single rod cylinders, 16 MPa (160 bar) compact series with bores from 250 mm to 500 mm －Accessory mounting dimensions
液压传动－单杆缸，16MPa(160bar)，缸径250mm至500mm的小型系列－附件安装尺寸
ISO 15552:2004
（2008）
Pneumatic fluid power — Cylinders with detachable mountings,
1 000 kPa (10 bar) series, bores from 32 mm to 320 mm —
Basic, mounting and accessories dimensions
气压传动－可分离安装的，1 000 kPa (10 bar)系列，缸内径32mm～320mm的气缸－基本尺寸、安装尺寸和附件尺寸
ISO 16656:2004
（2007）
Hydraulic fluid power － Single rod, short-stroke cylinders with bores from 32mm to 100mm for use at 10MPa (100bar)－ Mounting dimensions
液压传动 — 单杆短行程缸，内径32mm 至 100mm用于10MPa (100bar) — 安装尺寸
ISO/TR 16806:2003
Amd.1:2005
 (2006)
Pneumatic fluid power - Cylinders  －Load capacity of pneumatic slides and their presentation method
气压传动—缸—气动滑块的负荷容量及其描述方法
ISO 21287:2004
（2008）
Pneumatic fluid power － Cylinders －Compact cylinders, 1000kPa(10bar) series, bores from 20mm to 100mm 
气压传动—缸－紧凑型，1000kPa(10bar)系列，缸径20mm至100mm
TC131/SC4  管接头及同类产品和元件
ISO 1179-1:2007
Connections for general use and fluid power － Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing － Part 1: Threaded ports
一般用途和流体传动用管接头－ISO 228-1（非密封管螺纹）螺纹及橡胶或金属对金属密封件的油口和螺柱端－第1部分：螺纹油口
ISO 1179-2:2007
Connections for general use and fluid power － Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing － Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E)
一般用途和流体传动用管接头－ISO 228-1螺纹及橡胶或金属对金属密封件的油口和螺柱端－第2部分：带橡胶密封件（E型）的重型（S系列）和轻型（L系列）螺柱端
ISO 1179-3:2007
Connections for general use and fluid power － Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing － Part 3: Light-duty (L series) stud ends with sealing by O-ring with retaining ring (types G and H)
一般用途和流体传动用管接头－ISO 228-1螺纹及橡胶或金属对金属密封件的油口和螺柱端－第3部分：带O形圈及挡圈密封的轻型（L系列）螺柱端
ISO 1179-4:2007
Connections for general use and fluid power － Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing － Part 4: Stud ends for general use only with metal-to-metal sealing (type B)
一般用途和流体传动用管接头－ISO 228-1螺纹及橡胶或金属对金属密封件的油口和螺柱端－第4部分：一般仅用于金属对金属密封（B型）的螺柱端
ISO 4397:1993
Fluid power systems and components －Connectors and associated components －Nominal outside diameters of tubes and nominal inside diameters of hoses
流体传动系统和元件－管接头及其相关元件－标称的硬管外径和软管内径
ISO 4399:1995
Fluid power systems and components －Connectors and associated components －Nominal pressures
流体传动系统和元件－管接头及其相关元件－ 公称压力
ISO 6149-1:2006
Connections for fluid power and general use – Ports and stud ends with ISO 261 metric threads and O-ring sealing – Part 1: Port with truncated housing for O-ring seal  
用于流体传动和一般用途的管接头－带ISO261米制螺纹和O形圈密封的油口和螺柱端－第1部分：带O形圈用锪孔沟槽的油口
ISO 6149-2:2006
Connections for fluid power and general use －Ports and stud ends with ISO 261 metricthreads and O-ring sealing －Part 2: Dimensions, design, test methods and requirements for heavy-duty (S series) stud ends
用于流体传动和一般用途的管接头－带ISO261螺纹和O形圈密封的油口和螺柱端－第2部分： 重型（S系列）螺柱端的尺寸、型式、试验方法和技术要求
ISO 6149-3:2006
Connections for fluid power and general use －Ports and stud ends with ISO 261 threads and O-ring sealing －Part 3: Dimensions, design, test methods and requirements for light-duty (L series) stud ends
用于流体传动和一般用途的管接头－带ISO261螺纹和O形圈密封的油口和螺柱端－第3部分：轻型（L系列）螺柱端的尺寸、型式、试验方法和技术要求
ISO 6149-4:2006
Connections for fluid power and general use – Ports and stud ends with ISO 261 metric threads and O-ring sealing – Part 4: Dimensions, design, test methods and requirements for external hex and internal hex port plugs
用于流体传动和一般用途的管接头－带ISO261米制螺纹和O形圈密封的油口和螺柱端－第4部分：外六角和内六角油口螺塞的尺寸、型式、试验方法和技术要求
ISO 6150:1988
Pneumatic fluid power －Cylindrical quick-action couplings for maximum working pressures of 10 bar, 16 bar and 25 bar (1 MPa, 1,6 Mpa, and 2,5 MPa) －Plug connecting dimensions, specifications, application guidelines and testing
气压传动－最高工作压力10，16和25bar(1，1.6和2.5MPa) 圆柱形快换接头－插头连接尺寸，技术要求，应用指南和试验
ISO 6162-1:2002
Cor.1:2004
Hydraulic fluid power －Flange connections with split or one-piece flange clamps and metric or inch screws －Part 1:Flange connectors for use at pressures of 3,5 MPa(35 bar) to 35 MPa to 350 bar) ,DN 13 to DN 127
液压传动－带有分体式或整体式法兰以及米制或英制螺栓的法兰管接头－第1部分：用于3.5MPa(35bar)至35 MPa（350bar）压力下，DN 13 至DN 127的法兰管接头
ISO 6162-2:2002
Hydraulic fluid power －Flange connections with split or one-piece flange clamps and metric or inch screws －Part 2:Flange connectors for use at pressures of 35 MPa(350 bar) to 40 MPa （400 bar）,DN 13 to DN 51
液压传动－带有分体式或整体式法兰以及米制或英制螺栓的法兰管接头－第2部分：用于35MPa(350bar)至40 MPa（400bar）压力下，DN 13 至DN 51的法兰管接头
ISO 6164:1994
(2003)
Hydraulic fluid power－Four-screw, one-piece square-flange connections for use at pressures of 25 MPa and 40 MPa (250 bar and 400 bar)
液压传动－25MPa至40MPa(250bar至400bar)压力下使用的四螺栓整体方法兰
ISO 6605:2002
（2008）
Hydraulic fluid power －Hose and hose assemblies －Test method
液压传动－软管和软管总成－试验方法
ISO 7241-1:1987
Hydraulic fluid power －Quick-action couplings －Part 1: Dimensions and requirements
液压传动－快换接头－第1部分：尺寸和要求
ISO 7241-2:2000
Hydraulic fluid power －Quick-action couplings －Part 2: Test methods
液压传动－快换接头－第2部分：试验方法
ISO 8434-1:2007
Metallic tube connections for fluid power and general use －Part 1: 24 degree cone connectors
用于流体传动和一般用途的金属管接头－第1部分：24°锥形管接头
ISO 8434-2:2007
Metallic tube connections for fluid power and general use －Part 2: 37 degree flared fittings
用于流体传动和一般用途的金属管接头－第2部分：37°扩口式管接头
ISO 8434-3:2005
(2008)
Metallic tube connections for fluid power and general use －Part 3: O-ring face seal fittings
用于流体传动和一般用途的金属管接头－第3部分：O形圈端面密封管接头
ISO8434-6:2009
Metallic tube connections for fluid power and general use – Part 6: 60 degree cone connectors with or without O-ring
用于流体传动和一般用途的金属管接头－第6部分：带或不带O形圈密封的60°锥形管接头
ISO 9974-1:1996
（2006）
Connections for general use and fluid power －Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing －Part 1: Threaded ports
用于一般用途和流体传动的管接头－带ISO261螺纹用橡胶或金属密封的油口和螺柱端－第1部分：螺纹油口
ISO 9974-2:1996
（2006）
Connections for general use and fluid power －Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing －Part 2: Stud ends with elastomeric sealing (type E)
用于一般用途和流体传动的管接头－带ISO261螺纹用橡胶或金属密封的油口和螺杆柱端－第2部分：带橡胶密封的螺柱端（E型）
ISO 9974-3:1996
（2006）
Connections for general use and fluid power －Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing －Part 3: Stud ends with metal-to-metal sealing (type B)
用于一般用途和流体传动的管接头－带ISO261螺纹用橡胶或金属密封的油口和螺柱端－第3部分：带金属密封的螺柱端（B型）
ISO 9974-4:2006
Connections for general use and fluid power －Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing －Part 4: Dimensions, design, test methods and requirements for external hex and internal hex port plugs
用于一般用途和流体传动的管接头－带ISO 261（米制）螺纹用橡胶密封或金属对金属密封的油口和螺柱端－第4部分：外六角和内六角油口螺塞
ISO 10763:1994
Hydraulic fluid power －Plain-end, seamless and welded precision steel tubes －Dimensions and nominal working pressures
液压传动－端面平齐的无缝和焊接型精密钢管－尺寸及标称压力
ISO 11926-1:1995
Connections for general use and fluid power －Ports and stud ends with ISO 725 threads and O-ring sealing －Part 1: Ports with O-ring seal in truncated housing
用于一般用途和流体传动的管接头－带ISO725（英制）螺纹和O形圈密封的油口和螺柱端－第1部分：锪孔沟槽中装有O形密封圈的油口
ISO 11926-2:1995
Connections for general use and fluid power －Ports and stud ends with ISO 725 threads and O-ring sealing －Part 2: Heavy-duty (S series) stud ends
用于一般用途和流体传动的管接头－带ISO725螺纹和O形圈密封的油口和螺柱端－第2部分：重型（S系列）螺柱端
ISO 11926-3:1995
Connections for general use and fluid power －Ports and stud ends with ISO 725 threads and O-ring sealing －Part 3: Light-duty (L series) stud ends
用于一般用途和流体传动的管接头－带ISO725螺纹和O形圈密封的油口和螺柱端－第3部分：轻型（L系列）螺柱端
ISO 12151-1:2010
Connections for hydraulic fluid power and general use －Hose fittings －Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends
用于液压传动和一般用途的管接头－软管接头－第1部分:带ISO 8434-3的O形圈端面密封端头的软管接头
ISO 12151-2:2003
（2008）
Connections for hydraulic fluid power and general use －Hose fittings －Part 2: Hose fittings with ISO 8434-1 and ISO 8434-4 24°cone connector ends with O-rings
用于液压传动和一般用途的管接头－软管接头－第2部分:带ISO 8434－1和 ISO 8434－4的具有O形圈的24°锥形端头的软管接头
ISO 12151-3:2010
Connections for hydraulic fluid power and general use －Hose fittings －Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends
用于液压传动和一般用途的管接头－软管接头－第3部分:带ISO 6162-1或ISO 6162-2法兰端头的软管接头
ISO 12151-4:2007
Connections for hydraulic fluid power and general use －Hose fittings －Part 4: Hose fittings with ISO 6149 metric stud ends
用于液压传动和一般用途的管接头－软管接头－第4部分:带ISO 6149米制螺柱端的软管接头
ISO 12151-5:2007
Connections for hydraulic fluid power and general use －Hose fittings －Part 5: Hose fittings with ISO 8434-2 37 degree flared ends
用于液压传动和一般用途的管接头－软管接头－第5部分: 带ISO 8434-2　37°扩口端头的软管接头
ISO 12151-6:2009
Connections for hydraulic fluid power and general use – Hose fittings – Part 6: Hose fittings with ISO 8434-6 60 degree cone ends
用于液压传动和一般用途的管接头－软管接头－第6部分:带ISO8434-6 60°锥形端头的软管接头
ISO 14743:2004
（2008）
Pneumatic fluid power －Push-in connectors for thermoplastic tubes
气压传动－适用于热塑性塑料管的插入式管接头
ISO 15171-1:1999
（2004）
Connections for fluid power and general use －Hydraulic couplings for diagnostic purposes －Part 1: Coupling not for connection under pressure
用于流体传动和一般用途的管接头――诊断用液压管接头――第1部分：非压力下连接的管接头
ISO 15171-2:2000
（2005）
Connections for fluid power and general use －Hydraulic couplings for diagnostic purposes －Part 2: Coupling with M16 x 2 end for connection under pressure
用于流体传动和一般用途的管接头－诊断用液压管接头－第2部分:带M16×2螺纹端头的压力连接接头
ISO 16028:1999
Amd.1:2006
(2004)
Hydraulic fluid power －Flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31,5 MPa (315 bar) －Specifications
液压传动－用于压力为20MPa (200bar) 到 31,5MPa (315bar)的平面对接型快换接头－技术条件
ISO 17165-1:2007
Hydraulic fluid power — Hose assemblies — Part 1: Dimensions and requirements
液压传动－软管总成－第1部分：尺寸和要求
ISO/TR17165-2:2006
Hydraulic fluid power — Hose assemblies — Part 2: Recommended practices for hydraulic hose assemblies
液压传动－软管总成－第2部分：对于液压软管总成推荐的做法
ISO 19879:2010
 
Metallic tube connections for fluid power and general use —Test methods for hydraulic fluid power connections
用于流体传动和一般用途的金属管连接－液压传动用管接头的试验方法
TC131/SC5  控制产品及元件
ISO 4400:1994
（2009）
Fluid power systems and components － Three-pin electrical plug connectors with earth contact －Characteristics and requirements
流体传动系统和元件－带接地触点的三脚电插头－特性和要求
ISO 4401:2005
Hydraulic fluid power － Four-port directional control valves －Mounting surfaces
液压传动－四油口方向控制阀－安装面
ISO 4411:2008
Hydraulic fluid power － Valves －Determination of pressure differential/flow characteristics
液压传动－阀－压差/流量特性的测定
ISO 5599-1:2001
Cor.1:2007
Pneumatic fluid power － Five-port directional control valves －Part 1: Mounting interface surfaces without electrical connector
气压传动－五气口方向控制阀－第1部分：不带电插头的安装面
ISO 5599-2:2001
Amd 1:2004
Cor 1:2007
Pneumatic fluid power － Five-port directional control valves －Part 2: Mounting interface surfaces with optional electrical connector
气压传动－五气口方向控制阀－第2部分：带可选电插头的安装面
ISO 5599-3:1990
（2000）
Pneumatic fluid power － Five-port directional control valves －Part 3: Code system for communication of valve functions
气压传动－五气口方向控制阀－第3部分：表示阀功能的标注方法
ISO 5781:2000
Hydraulic fluid power － Pressure-reducing valves, sequence valves, unloading valves, throttle valves and check valves －Mounting surfaces
液压传动－减压阀、顺序阀、卸荷阀、节流阀和单向阀－安装面
ISO 5782-1:1997
（2007）
Pneumatic fluid power － Compressed-air filters －Part 1: Main characteristics to be included in suppliers' literature and product marking requirements
气压传动－压缩空气过滤器－第1部分：商务文件和具体要求中应包含的主要特性
ISO 5782-2:1997
（2007）
Pneumatic fluid power －Compressed-air filters －Part 2: Test methods to determine the main characteristics to be included in supplier's literature
气压传动－压缩空气过滤器－第2部分：商务文件中应包含主要特性检验的试验方法
ISO 5783:1995
Hydraulic fluid power － Code for identification of valve mounting surfaces and cartridge valve cavities
液压传动－阀安装面和插装阀孔的标识规则
ISO 5784-1:1988
Fluid power systems and components － Fluid logic circuits －Part 1: Symbols for binary logic and related functions
流体传动系统和元件－流体逻辑回路－第1部分：二进制逻辑及相关功能的符号
ISO 5784-2:1989
Fluid power systems and components － Fluid logic circuits －Part 2: Symbols for supply and exhausts as related to logic symbols
流体传动系统和元件－流体逻辑回路－第2部分：与逻辑符号相关的供气和排气符号
ISO 5784-3:1989
Fluid power systems and components － Fluid logic circuits －Part 3: Symbols for logic sequencers and related functions
流体传动系统和元件－流体逻辑回路－第3部分：逻辑顺序器及相关功能的符号
ISO 6263:1997
Hydraulic fluid power － Compensated flow-control valves －Mounting surfaces
液压传动－补偿型流量控制阀－安装面
ISO 6264:1998
Hydraulic fluid power － Pressure-relief valves －Mounting surfaces
液压传动－溢流阀－安装面
ISO 6301-1:2009
Pneumatic fluid power — Compressed-airlubricators —Part 1:Main characteristics to be included in supplier's literature and product-marking requirements
气压传动－压缩空气油雾器－第1部分：在供应商文件和产品标志要求中包含的主要特性
ISO 6301-2:2006
Pneumatic fluid power － Compressed-air lubricators －Part 2: Test methods to determine the main characteristics to be included in supplier's literature
气压传动－压缩空气油雾器－第2部分：测定供应商文件中包含的主要特性的试验方法
ISO 6358:1989
Pneumatic fluid power － Components using compressible fluids －Determination of flow-rate characteristics
气压传动－可压缩流体元件－流量特性的测定
ISO 6952:1994
Fluid power systems and components － Two-pin electrical plug connectors with earth contact －Characteristics and requirements
流体传动系统和元件－带接地触点的两脚电插头－特性和要求
ISO 6953-1:2000
Cor.1:2006
Pneumatic fluid power － Compressed air pressure regulators and filter-regulators －Part 1: Main characteristics to be included in literature from suppliers and product-marking requirements
气压传动－压缩空气调压阀和带过滤器的调压阀－第1部分：商务文件中包含的主要特性及产品标识要求
ISO 6953-2:2000
Pneumatic fluid power － Compressed air pressure regulators and filter-regulators －Part 2: Test methods to determine the main characteristics to be included in literature from suppliers
气压传动－压缩空气调压阀和带过滤器的调压阀－第2部分：评定商务文件中包含的主要特性的试验方法
ISO 7368:1989
Hydraulic fluid power － Two-port slip-in cartridge valves －Cavities
液压传动－二通盖板式插装阀－插装孔
ISO 7789:2007
Hydraulic fluid power － Two-, three- and four-port screw-in cartridge valves －Cavities
液压传动－二油口、三油口和四油口螺纹式插装阀－插装孔
ISO 7790:1997
Hydraulic fluid power － Four-port modular stack valves and four-port directional control valves, sizes 02, 03 and 05 －Clamping dimensions
液压传动－四油口叠加阀和四油口方向控制阀，02，03和05规格－夹紧尺寸
ISO 8778:2003
(2008)
Pneumatic fluid power － Standard reference atmosphere
气压传动－标准参考大气
ISO 9461:1992
（2008）
Hydraulic fluid power － Identification of valve ports, subplates, control devices and solenoids
液压传动－阀的油口、底板、控制装置和电磁铁的标注
ISO 10041-1:2010
 
Pneumatic fluid power — Electropneumatic continuous flow control
valves — Part 1: Main characteristics to include in the supplier's iterature
气压传动－电气-气动连续流量控制阀－第1部分：包含在供应商销售文件中的主要特性
ISO 10041-2:2010
 
Pneumatic fluid power — Electropneumatic continuous flow control
valves — Part 2: Test methods to determine main characteristics to include in the supplier's literature
气压传动－电气-气动连续流量控制阀－第2部分：确定包含在供应商销售文件中的主要特性的测试方法
ISO 10094-1:2010
 
Pneumatic fluid power — Electropneumatic pressure control valves —
Part 1: Main characteristics to include in the supplier's literatu
气压传动－电气-气动压力控制阀－第1部分：包含在供应商销售文件中的主要特性
ISO 10094-2:2010
 
Pneumatic fluid power — Electropneumatic pressure control valves —
Part 2: Test methods to determine main characteristics to include in the
supplier's literature
气压传动－电气-气动压力控制阀－第2部分：包含在供应商销售文件中的主要特性的评定方法
ISO 10372:1992
Hydraulic fluid power － Four- and five-port servovalves －Mounting surfaces
液压传动－四油口和五油口伺服阀－安装面
ISO 11727:1999
Pneumatic fluid power － Identification of ports and control mechanisms of control valves and other components
气压传动－控制阀和其他元件的气口、控制机构的标注
ISO 12238:2001
Pneumatic fluid power － Directional control valves －Measurement of shifting time
气压传动－方向控制阀－切换时间的测量
ISO 15217:2000
Fluid power systems and components － 16 mm square electrical connector with earth contact －Characteristics and requirements
流体传动系统和元件－带接地点的16mm方形电插头－特性和要求
ISO 15218:2003
Pneumatic fluid power －3/2 solenoid valves －Mounting interface surfaces
气压传动—两位三通电磁阀－安装面
ISO 15407-1:2000
Pneumatic fluid power － Five-port directional control valves, sizes 18 mm and 26 mm －Part 1: Mounting interface surfaces without electrical connector
气压传动－五气口方向控制阀, 18mm和26mm规格－第1部分：不带电插头的安装面
ISO 15407-2:2003
（2008）
Pneumatic fluid power － Five-port directional control valves, sizes 18 mm and 26 mm －Part 2: Mounting interface surfaces with optional electrical connector
气压传动－五气口方向控制阀, 18mm和26mm规格－第2部分：带可选择电插头的安装面
ISO 16873:2002
Amd 1:2005
（2008）
Hydraulic fluid power －Pressure switches－Mounting surfaces
液压传动－压力开关－安装面
ISO 16874:2004
（2008）
Hydraulic fluid power － Identification of manifold assemblies and their components
液压传动－油路块总成及其元件的标识
ISO 17082:2004
Pneumatic fluid power － Valves －Data to be included in commercial literature
气压传动—阀—商务文件中应包含的资料
ISO 20401:2005
Cor 1:2005
 (2008)
Pneumatic fluid power systems－Directional control valves －Specification of pin assignment for electrical roud connectors of diameters 8 mm and 12 mm
气动系统－方向控制阀－直径8～12mm圆形电插头的管脚分配规范
TC131/SC6  污染控制
ISO 2941:2009
Hydraulic fluid power －Filter elements －Verification of collapse/burst pressure rating
液压传动－滤芯－压溃/破裂额定压力的验证
ISO 2942:2004
（2007）
Hydraulic fluid power － Filter elements －Verification of fabrication integrity and determination of the first bubble point
液压传动－滤芯－结构完整性的验证和第一气泡点的测定
ISO 2943:1998
（2009）
Hydraulic fluid power － Filter elements －Verification of material compatibility with fluids
液压传动－滤芯－材料与油液相溶性的验证
ISO 3722:1976
（2008）
Hydraulic fluid power － Fluid sample containers －Qualifying and controlling cleaning methods
液压传动－油液取样容器－检验和控制净化方法
ISO 3723:1976
（2008）
Hydraulic fluid power － Filter elements －Method for end load test
液压传动－滤芯－端载荷试验方法
ISO 3724:2007
（2010）
Hydraulic fluid power － Filter elements － Determination of resistance to flow fatigue using particulate contaminant
液压传动－滤芯－利用颗粒污染物测定抗流动疲劳特性
ISO 3938:1986
（2006）
Hydraulic fluid power － Contamination analysis －Method for reporting analysis data
液压传动－污染分析－报告分析数据的方法
ISO 3968:2001
Cor 1:2002
（2006、2011）
Hydraulic fluid power － Filters －Evaluation of differential pressure versus flow characteristics
液压传动－过滤器－压降流量特性的评定
ISO 4021:1992
（2008）
Hydraulic fluid power － Particulate contamination analysis －Extraction of fluid samples from lines of an operating system
液压传动－颗粒污染分析－从工作系统管路中提取油样
ISO 4405:1991
Hydraulic fluid power － Fluid contamination －Determination of particulate contamination by the gravimetric method
液压传动－油液污染－用称重法测定颗粒污染
ISO 4406:1999
（2004）
Hydraulic fluid power － Fluids －Method for coding the level of contamination by solid particles
液压传动－油液－固体颗粒污染等级代号法
ISO 4407:2002
（2007）
Hydraulic fluid power － Fluid contamination －Determination of particulate contamination by the counting method using an optical microscope
液压传动－油液污染－用光学显微镜计数法测定颗粒污染
ISO/TR10949:2002
（2005）
Hydraulic fluid power – Component cleanliness – Guidelines for  achieving and controlling cleanliness of components from  manufacture to installation
液压传动—元件清洁度—从制造到安装达到和控制元件清洁度的准则
ISO 11170:2003
Hydraulic fluid power － Filter elements －Procedure for verifying performance characteristics
液压传动－滤芯－检验性能特性的程序
ISO 11171:2010
 
Hydraulic fluid power － Calibration of automatic particle counters for liquids
液压传动－液体自动颗粒计数器的校准
ISO 11500:2008
Hydraulic fluid power － Determination of the particulate contamination level of a liquid sampleby automatic particle counting using the light-extinction principle
液压传动－利用遮光原理通过自动颗粒计数测定液样颗粒污染等级
ISO 11943:1999
Hydraulic fluid power － On-line automatic particle-counting systems for liquids －Methods of calibration and validation
液压传动－在线液体自动颗粒计数系统－校准和验证的方法
ISO/TR 16144:2002
Hydraulic fluid power – Calibration of liquid automatic particle counters – Procedures used to certify the standard reference material SRM 2806
液压传动—液体自动颗粒计数器的校准—用于验证标准参考物质SRM2806的程序
ISO/TR 16386:1999
(2005)
Impact of changes in ISO fluid power particle counting － Contamination control and filter test standards
改变ISO流体传动颗粒计数、污染和过滤标准的影响
ISO /TS 16431:2002
 (2005)
Hydraulic fluid power – Assembled systems – Verification of cleanliness
液压传动－系统总成－清洁度的检验
ISO 16860:2005
Hydraulic fluid power filters －Filter － Test Method for differential pressure devices
液压传动－过滤器－压差装置的试验方法
ISO 16889:2008
Hydraulic fluid power － filters －Multi-pass method for evaluating filtration performance of a filter element
液压传动－过滤器－评定滤芯过滤性能的多次通过法
ISO 18413:2002
Hydraulic fluid power – Cleanliness of parts and components – Inspection document and principles related to  sample collection, sample analysis and data reporting
液压传动—零件和元件的清洁度—与污染物收集、分析和数据报告相关的检验文件和准则
ISO 23181:2007
Hydraulic fluid power － Filter elements － Determination of resistance to flow fatigue using high viscosity fluid
液压传动－滤芯－用高黏度油液测定抗流动疲劳特性
ISO 23309:2007
Hydraulic fluid power systems —Assembled systems — Methods of
cleaning lines by flushing
液压传动系统－系统总成－管路的冲洗方法
ISO 21018-1:2008
Hydraulic fluid power － Monitoring the level of particulate contamination of the fluid － Part 1: General principles
液压传动—油液颗粒污染等级监测—第1部分：通则
ISO 21018-3:2008
Hydraulic fluid power － Monitoring the level of particulate contamination of the fluid － Part 3: Use of the filter blockage technique
液压传动—油液颗粒污染等级监测—第3部分：利用滤膜阻塞技术
ISO 27407:2010
Hydraulic fluid power — Marking of performance characteristics on hydraulic filters
液压传动—液压过滤器性能特性的标识
TC131/SC7  密封装置
ISO 3601-1:2012
Fluid power systems － O-rings －Part 1: Inside diameters, cross-sections, tolerances and designation code
流体传动系统－O形圈－第1部分：内径、断面、公差和名称代号
ISO 3601-2:2008
Cor.1:2009
Cor.2:2009
Fluid power systems － O-rings － Part 2: Housing dimensions for general applications
流体传动系统－O形圈－第2部分：一般应用的沟槽尺寸
ISO 3601-3:2005
（2009）
Fluid power systems － O-rings －Part 3: Quality acceptance criteria
流体传动系统－O形圈－第3部分：质量验收准则
ISO 3601-4:2008
Fluid power systems － O-rings －Part 4: Anti-extrusion rings (back-up rings)
流体传动系统－O形圈－第4部分：防挤出圈（挡圈）
ISO 3601-5:2002
Fluid power systems －O-rings －Part 5: suitability of elastomeric materials for industrial applications
流体传动系统－O形圈－第3部分：合成橡胶材料的工业适用性
ISO 3939:1977
（2008）
Fluid power systems and components － Multiple lip packing sets －Methods for measuring stack heights
流体传动系统和元件－多层唇形密封组件－测量叠合高度的方法
ISO 5597:2010
Hydraulic fluid power － Cylinders －Housings for piston and rod seals in reciprocating applications －Dimensions and tolerances
液压传动－缸－往复用活塞和活塞杆密封沟槽－尺寸和公差
ISO 6072:2002
Hydraulic fluid power － Compatibility between fluid and standard elastomeric materials
液压传动－油液与标准合成橡胶材料的相容性
ISO 6194-1:2007
Rotary shaft lip-type seals incorporating elastomeric sealing elements － Part 1: Nominal dimensions and tolerances
密封元件为弹性体材料的旋转轴唇形密封件－第1部分：名义尺寸和公差
ISO 6194-2:2009
Rotary shaft lip-type seals incorporating elastomeric sealing elements -- Part 2: Vocabulary
密封元件为弹性体材料的旋转轴唇形密封件－第2部分：词汇
ISO 6194-3:2009
Rotary shaft lip type seals － Part 3: Storage, handling and installation
密封元件为弹性体材料的旋转轴唇形密封件－第3部分：储存，运输和安装
ISO 6194-4:2009
Rotary shaft lip-type seals incorporating elastomeric sealing elements － Part 4: Performance test procedures
密封元件为弹性体材料的旋转轴唇形密封件－第4部分：性能试验程序
ISO 6194-5:2008
Rotary-shaft lip-type seals incorporating elastomeric sealing elements － Part 5: Identification of visual imperfections
密封元件为弹性体材料的旋转轴唇形密封件－第5部分：外观缺陷的鉴定
ISO 6195:2002
(2008)
Fluid power systems and components － Cylinder-rod wiper-ring housings in reciprocating applications －Dimensions and tolerances
流体传动系统和元件－往复用缸活塞杆防尘圈沟槽－尺寸和公差
ISO 6547:1981
Hydraulic fluid power － Cylinders －Piston seal housings incorporating bearing rings －Dimensions and tolerances
液压传动－缸－装有支撑环的活塞密封沟槽－尺寸和公差
ISO 7425-1:1988
Hydraulic fluid power －Housings for elastomer-energized, plastic-faced seals －Dimensions and tolerances －Part 1: Piston seal housings
液压传动－弹性体赋能的塑料面密封件的沟槽－尺寸和公差－第1部分：活塞密封沟槽
ISO 7425-2:1989
Hydraulic fluid power －Housings for elastomer-energized, plastic-faced seals －Dimensions and tolerances －Part 2: Rod seal housings
液压传动－弹性体赋能的塑料面密封件的沟槽－尺寸和公差－第2部分：活塞杆密封沟槽
ISO 7986:1997
（2008）
Hydraulic fluid power － Sealing devices －Standard test methods to assess the performance of seals used in oil hydraulic reciprocating applications
液压传动－密封装置－评定用于液压往复运动的密封件性能的标准试验方法
ISO 10766:2006
Hydraulic fluid power － Cylinders －Housing dimensions for rectangular-section-cut bearing rings for pistons and rods
液压传动－缸－活塞和活塞杆用矩形断面开口支撑环沟槽尺寸
ISO 16589-1:2011
Rotary shaft lip-type seals incorporating thermoplastic sealing elements－Part1: Nomonal dimension and tolerances
密封元件为热塑性材料的旋转轴唇形密封件－第1部分：名义尺寸和公差
ISO 16589-2:2001
Rotary shaft lip-type seals incorporating thermoplastic sealing elements－Part2: vocabulary
密封元件为热塑性材料的旋转轴唇形密封件－第2部分：术语
ISO 16589-3:2011
Rotary shaft lip-type seals incorporating thermoplastic sealing elements－Part3: Storage, handling and installation
密封元件为热塑性材料的旋转轴唇形密封件－第3部分：贮存、操作和安装
ISO 16589-4:2011
Rotary shaft lip-type seals incorporating thermoplastic sealing elements－Part4: Performance test procedures
密封元件为热塑性材料的旋转轴唇形密封件－第4部分：性能试验程序
ISO 16589-5:2011
Rotary shaft lip-type seals incorporating thermoplastic sealing elements－Part5: Identification of visual imperfections
密封元件为热塑性材料的旋转轴唇形密封件－第5部分：可视缺陷标识
TC131/SC8  产品试验
ISO 4392-1:2002
（2007）
Hydraulic fluid power － Determination of characteristics of motors －Part 1: At constant low speed and at constant pressure
液压传动－马达特性的测定－第1部分：在恒低速和恒压力下
ISO 4392-2:2002
（2007）
Hydraulic fluid power － Determination of characteristics of motors －Part 2: Startability
液压传动－马达特性的测定－第2部分：起动性
ISO 4392-3:1993
（2009）
Hydraulic fluid power － Determination of characteristics of motors －Part 3: At constant flow and at constant torque
液压传动－马达特性的测定－第3部分：在恒流量和恒转矩下
ISO 4409:2007
Hydraulic fluid power － Positive-displacement pumps, motors and integral transmissions － Methods of testing and presenting basic steady-state performance
液压传动－容积式泵、马达和整体式传动装置－基本稳态性能的试验及表达方法
ISO 4412-1:1991
（2006）
Hydraulic fluid power － Test code for determination of airborne noise levels －Part 1: Pumps
液压传动－测定空气传播噪声等级的试验规范－第1部分：泵
ISO 4412-2:1991
（2006）
Hydraulic fluid power － Test code for determination of airborne noise levels －Part 2: Motors
液压传动－测定空气传播噪声等级的试验规范－第2部分：马达
ISO 4412-3:1991
（2006）
Hydraulic fluid power － Test code for determination of airborne noise levels－Part 3: Pumps－Method using a parallelepiped microphone array
液压传动－测定空气传播噪声等级的试验规范－第3部分：泵，采用平行六面体传声器阵列的方法
ISO 6403:1988
（2009）
Hydraulic fluid power － Valves controlling flow and pressure －Test methods
液压传动－控制流量和压力的阀－试验方法
ISO 8426:2008
Hydraulic fluid power － Positive displacement pumps and motors －Determination of derived capacity
液压传动－容积式泵和马达－空载排量的测定
ISO 9110-1:1990
（2005）
Hydraulic fluid power － Measurement techniques －Part 1: General measurement principles
液压传动－测量技术－第1部分：通用测量准则
ISO 9110-2:1990
（2005）
Hydraulic fluid power － Measurement techniques －Part 2: Measurement of average steady-state pressure in a closed conduit
液压传动－测量技术－第2部分：密闭回路中平均稳态压力的测量
ISO 10767-1:1996
（2006）
Hydraulic fluid power－Determination of pressure ripple levels generated in systems and components －Part 1: Precision method for pumps
液压传动－系统和元件产生压力波动值的测定－第1部分：用于泵的精密方法
ISO 10767-2:1999
（2004）
Hydraulic fluid power－Determination of pressure ripple levels generated in systems and components －Part 2: Simplified method for pumps
液压传动－系统和元件产生压力波动值的测定－第2部分：用于泵的简化方法
ISO 10767-3:1999
（2004）
Hydraulic fluid power － Determination of pressure ripple levels generated in systems and components －Part 3: Method for motors
液压传动－系统和元件产生压力波动值的测定－第3部分：用于马达的方法
ISO 10770-1:2009
Hydraulic fluid power － Electrically modulated hydraulic control valves －Part 1: Test methods for four-way directional flow control valves
液压传动－电调节液压控制阀－第1部分：四通方向控制阀试验方法
ISO 10770-2:1998
（2009）
Hydraulic fluid power － Electrically modulated hydraulic control valves －Part 2: Test methods for three-way directional flow control valves
液压传动－电调节液压控制阀－第2部分：三通方向控制阀试验方法
ISO 10770-3:2007
Hydraulic fluid power － Electrically modulated hydraulic control valves －Part 3: Test methods for pressure control valves
液压传动－电调节液压控制阀－第3部分：压力控制阀试验方法
ISO 10771-1:2002
Hydraulic fluid power － Fatigue pressure testing of metal pressure-containing envelopes－Part 1: Test method
液压传动－金属压力容器的疲劳压力试验－第1部分：试验方法
ISO/TR 10771-2:2008
Hydraulic fluid power－Fatigue pressure testing of metal pressure-containing envelopes － Part 2: Rating methods
液压传动－金属压力容器的疲劳压力试验－第2部分：评价方法
ISO 15086-1:2001
（2006）
Hydraulic fluid power － Determination of the fluid-borne noise characteristics of components and systems －Part 1: Introduction
液压传动－元件和系统油液传播噪声特性的测定－第1部分：通则
ISO 15086-2:2000
（2005）
Hydraulic fluid power － Determination of the fluid-borne noise characteristics of components and systems －Part 2: Measurement of the speed of sound in a fluid in a pipe
液压传动－元件和系统油液传播噪声特性的测定－第2部分：管路油液中声音速度的测量
ISO 15086-3:2008
Hydraulic fluid power － Determination of the fluid-borne noise characteristics of components and systems － Part 3: Measurement of hydraulic impedance
液压传动－元件和系统的油液传播噪声特性测定－第3部分：液压阻抗测量
 
ISO 16902-1:2003
（2008）
Hydraulic fluid power － Test code for the determination of sound power levels using sound intensity techniques: Engineering method －Part 1 : Pumps
液压传动—用声强技术测量声功率级的试验规则:工程方法―第1部分：泵
ISO 17559:2003
Hydraulic fluid power - Electrically controlled hydraulic pumps - Test methods to determine performance characteristics
液压传动－电控液压泵－测定性能特性的试验方法
ISO/TR19972-1:2009
Hydraulic fluid power – Methods to assess the reliability of hydraulic components – Part 1: General procedures and calculation method
液压传动－评价液压元件可靠性的方法－第1部分：一般程序和计算方法

TC131/SC9  装置和系统

ISO 4413:2010
Hydraulic fluid power － General rules and safety requirements for  systems and their components
液压传动－对系统及其元件的一般规则和安全要求
ISO 4414:2010
Pneumatic fluid power － General rules and safety requirements for  systems and their components
气压传动－对系统及其元件的一般规则和安全要求

 

最热资讯

最新资讯

 
关于艾逊 ｜ 法律声明 ｜ 商务合作 ｜ 招贤纳士 ｜ 友情链接
CopyRight © 2005-2011 MRO工业品-艾逊实业(上海). All Rights Reserved.